show sidebar & content

Archive for month: September, 2013

Side Chair Class: Day Six

29 Sep 2013 / 0 Comments / in Chairmaker's Journal

On the final day of class the only remaining tasks are to level the chair and weave the seat. Leveling the chair will remove any wobble introduced in the assembly process, allow all four legs to fully contact the floor, and drop the back of the chair about half an inch to make it more […]

Side Chair Class: Day Five

28 Sep 2013 / 0 Comments / in Chairmaker's Journal

Day five is very busy and very satisfying. We begin the day by shaping the ears at the top of the rear legs. I always have students practice on spare stock first. Only when they are comfortable with the process do they move onto shaping their actual legs, as David is doing here. You can […]

Side Chair Class: Day Four

27 Sep 2013 / 0 Comments / in Chairmaker's Journal

On day four we continue shaping the rear legs using the same process as the front legs but with the added complexity of a curved part. Here David has shaped the bottom of the rear leg to a tapered octagon and is checking his work. While David and Mark are working on the rear legs […]

Side Chair Class: Day Three

26 Sep 2013 / 0 Comments / in Chairmaker's Journal

Day three is devoted entirely to hand shaping the front and rear legs. The day begins with a practice front leg. Shaping with hand tools is often a new process for students and I like them to try the techniques and tools on practice stock before working on their actual chair parts. This is the […]

Side Chair Class: Day Two

25 Sep 2013 / 0 Comments / in Chairmaker's Journal

Day two begins with cutting mortises into the rear legs for the slat tenons. This is done while the legs are still square so that there is a flat reference surface. Here David is using the slat mortising jig to route the mortises into the tapered, inside face of one leg. For the opposite leg […]

Side Chair Class: Day One

24 Sep 2013 / 2 Comments / in Chairmaker's Journal

I am in the middle of two weeks of teaching and don’t have time to work on the next post in the side chair build series. As an alternative I thought it would be fun to document the class I am teaching this week. I have two students—Mark Hochstein and David Blois. Both are experienced […]

Boggs Side Chair Build: Chair Design, Part 1

19 Sep 2013 / 2 Comments / in Chairmaker's Journal

At this point in the side chair build I am ready to lay out slat mortises on the rear legs. But before I get into that part of the process I thought it would be a good idea to go over some general principles of chair design, especially as it relates to dining chairs. Understanding […]

September 2013 Newsletter

sculpted-hi-res
15 Sep 2013 / 0 Comments / in News

  September 2013 + ISSUE 10 Contact Us 828-398-9701 8 London Road Asheville, NC 28803 Stay Connected Spread the Word Forward to a Friend © *|CURRENT_YEAR|* *|LIST:COMPANY|* All rights reserved. | view email in browser | Unsubscribe *|EMAIL|*   This email was sent to *|EMAIL|*why did I get this?    unsubscribe from this list    update subscription preferences*|LIST:ADDRESSLINE|**|REWARDS|*

Boggs Side Chair Build: Post Bend Shaping—Rear Legs, Part 2

10 Sep 2013 / 2 Comments / in Chairmaker's Journal

Now that I have flattened, thicknessed, and trimmed the rear legs to length they are ready for the final two steps prior to slat mortising. The first step is to cut a relief cut into curved upper front face of each leg. This begins with laying out the cut. First I put a mark at […]

Boggs Side Chair Build: Post Bend Shaping—Rear Legs, Part 1

03 Sep 2013 / 0 Comments / in Chairmaker's Journal

The bending is complete and the rear legs have been drying in my drying closet for about a week. I always check the moisture content before removing the legs from the forms. In this case the legs have dried to about 8 or 9% moisture content so I remove them from the forms. I’m now […]